HP DESIGNJET T930, T930PS

Votre traceur HP DESIGNJET T930, T930PS est en panne ?

Notre technicien intervient sur site pour le dépanner.

Indiquez-nous le code erreur ou le problème rencontré pour obtenir un diagnostic ou un devis de réparation sur site.

Codes erreur les plus fréquents sur les traceurs HP DESIGNJET T930, T930PS

Code Erreur 02.1:10

Code Erreur 08:04

Code Erreur 08:11

Code Erreur 21:10 ou 21:13 ou message Maintenance recommandée

Code Erreur 47:01 ou 47:03

Code Erreur 79:04

Code Erreur 79.2:04

Code Erreur 86:01 ou Vérifier chemin des têtes d'impression ou Vérifier chemin papier

Message Repositionner la tête d'impression ou Remplacer la tête d'impression

Tableau de tous les codes erreurs de HP DESIGNJET T930, T930PS

01.0:10 HP DESIGNJET T930, T930PS

- id :

1258

- code :

01.0:10

- description :

Problem with the engine PCA

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: • Replace the engine PCA. See Engine PCA. NOTE: If the 1.:1 is not solved after replacing the engine PCA, or after replacing it a SE 2.1:1 code appears (carriage PCA), check the trailing cable to engine PCA connection; It's low probability, but possible, that a wrong connection could cause the damage to the carriag

01.1:10 HP DESIGNJET T930, T930PS

- id :

1259

- code :

01.1:10

- description :

Error in the engine PCA

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: • Replace the engine PCA. See Engine PCA NOTE: If the 1.1:1 is not solved after replacing the engine PCA, or after replacing it a SE 2.1:1 code appears (carriage PCA), check the trailing cable to engine PCA connection; It's low probability, but possible, that a wrong connection could cause the damage to the carriage

01.2:10 HP DESIGNJET T930, T930PS

- id :

1260

- code :

01.2:10

- description :

Problem with the backup NVM

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Check that the Encoder PCA Cable is correctly connected. 2. If the cable is correctly connected, replace the encoder PCA. See Motor Media Advance Transmission with Encoder. NOTE: The backup NVM is located in the Paper Path Encoder PCA. In order to replace this part, you need to order the service kit CR357-679 "

01.7:10 HP DESIGNJET T930, T930PS

- id :

1262

- code :

01.7:10

- description :

Communication errors between engine PCA and formatter

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Replace the formatter. 2. If the problem persists, replace the engine PCA.

02.1:10 HP DESIGNJET T930, T930PS

- id :

1263

- code :

02.1:10

- description :

Problem with the carriage PCA

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Check that the Trailing Cable is correctly connected between the Engine PCA and Carriage PCA. 2. Replace the carriage PCA. See Carriage PCA. NOTE: If the 2.1:1 is not solved after replacing the carriage PCA or after replacing it a SE 1.:1 or SE 1.1:1 code appears (engine PCA), check the trailing cable connection

03.2:10 HP DESIGNJET T930, T930PS

- id :

1264

- code :

03.2:10

- description :

Problem with the E-Box cooling fans

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Check the fans to see which is not rotating by checking for airflow coming from the ebox; place a hand over the fan holes in the ebox underneath the printer to check for air coming from both fans. 2. Remove the E-Box (see Open the E-Box) open it, and check that the cable of the nonfunctional cooling fan is correctly c

03:10 HP DESIGNJET T930, T930PS

- id :

1265

- code :

03:10

- description :

Problem with the power supply unit

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Check the cabling coming from the power supply to the Engine PCA. 2. Replace the PSU.

05.1:10 HP DESIGNJET T930, T930PS

- id :

1266

- code :

05.1:10

- description :

Problems with the formatter FAN

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: • Replace the formatter.

05.4:10 HP DESIGNJET T930, T930PS

- id :

1267

- code :

05.4:10

- description :

BIOS data corrupted in formatter

- remede :

Call agent: • Replace the formatter.

05.5:10 HP DESIGNJET T930, T930PS

- id :

1268

- code :

05.5:10

- description :

BIOS should be updated (advisory)

- remede :

Call agent: • Update the formatter BIOS.

05.7:10 HP DESIGNJET T930, T930PS

- id :

1269

- code :

05.7:10

- description :

Synchronization problems between control panel and formatter

- remede :

Call agent: 1. Disconnect any device connected to the USB host in the front panel. 2. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Replace the front panel. See Front panel. 2. If after replacing the front panel, the SE continues to appear; replace the formatter PCA.

06.1:10 HP DESIGNJET T930, T930PS

- id :

1270

- code :

06.1:10

- description :

Hard disk not detected

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Remove the E-Box (see Open the E-Box) open it, and check that the hard diskfs power and data cables are correctly connected. 2. Replace the hard disk drive. See Hard disk drive. 3. If after replacing the hard disk in the front panel the SE continues to appear; replace the formatter PCA.

06.2:10 HP DESIGNJET T930, T930PS

- id :

1271

- code :

06.2:10

- description :

Hard disk cannot be unlocked

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Remove the E-Box (see Open the E-Box) open it, and check that the hard disk’s power and data cables are correctly connected. 2. Replace the hard disk drive.

06.3:10 HP DESIGNJET T930, T930PS

- id :

1272

- code :

06.3:10

- description :

Hard disk is corrupted

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Remove the E-Box (see Open the E-Box) open it, and check that the hard diskfs power and data cables are correctly connected. 2. Replace the hard disk drive.

06:03, 06:10 HP DESIGNJET T930, T930PS

- id :

1273

- code :

06:03, 06:10

- description :

Problems with NVM in hard disk

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: • Replace the hard disk drive.

08:04 HP DESIGNJET T930, T930PS

- id :

1274

- code :

08:04

- description :

Communication lost between front panel and formatter

- remede :

Call agent: 1. Restart the printer. 2. Update the firmware. Service engineer: 1. Check that the front panel is correctly connected. 2. Replace the front panel. See Front panel. 3. If after replacing the front panel the SE continues to appear; replace the formatter PCA.

08:08 HP DESIGNJET T930, T930PS

- id :

1275

- code :

08:08

- description :

A front panel icon does not work (advisory)

- remede :

Service engineer: 1. Restart the printer. 2. Update the firmware.

08:10 HP DESIGNJET T930, T930PS

- id :

1276

- code :

08:10

- description :

Problems detected in the front panel Hardware

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Check that the front panel is correctly connected. 2. Replace the front panel.

08:11 HP DESIGNJET T930, T930PS

- id :

1277

- code :

08:11

- description :

Communication lost between front panel and printer

- remede :

Call agent: 1. Restart the printer. 2. Update the firmware. Service engineer: 1. Check that the front panel is correctly connected. 2. Replace the front panel. See Front panel. 3. If after replacing the front panel the SE continues to appear; replace the formatter PCA.

09:01 HP DESIGNJET T930, T930PS

- id :

1278

- code :

09:01

- description :

Media jam in Scanner

- remede :

Call agent: 1. Turn off the product using the power key at the front, then also turn off the power switch at the rear and disconnect the power cable. 2. There is a small lever at the rear left of the scanner. Slide the lever to the right and open the scanner cover. 3. Solve the media jam. 4. Check and clean the pressure rollers. 5. Close the scanner cover and gently push it down to lock it into place. 6. Reconnect the product’s power cable; turn on the power switch at the rear, and turn on th

09:01:10 HP DESIGNJET T930, T930PS

- id :

1279

- code :

09:01:10

- description :

Scanner Motor is failing

- remede :

Call agent: 1. Reboot the printer. 2. If system error persists, upgrade to the latest firmware. 3. Open the scanner cover. Underneath you will see red, then green, then blue flashing lights. 4. In the center of the scanner cover, between the flashing lights, you will find 4 small sensors labeled as R, G, B and L. Put your fingers over the R, G and B sensors simultaneously and the scanner motor should advance. Service engineer: 1. If there is no response from the scanner motor, replace the Eng

09:02 HP DESIGNJET T930, T930PS

- id :

1280

- code :

09:02

- description :

Scanner not calibrated

- remede :

• Calibrate the Scanner.

09:02:10 HP DESIGNJET T930, T930PS

- id :

1281

- code :

09:02:10

- description :

CIS A Element is failing

- remede :

Call agent: 1. Clean the scanner of dust and dirt and perform the Scanner Calibration. 2. If the system error persists, upgrade with latest firmware version. Service engineer: 1. Replace CIS A Element. 2. Replace Scanner Controller Board (SCU). See Scanner Controller Unit (SUP).

09:03 HP DESIGNJET T930, T930PS

- id :

1282

- code :

09:03

- description :

File I/O Error

- remede :

Call agent: 1. Reboot the product. 2. Upgrade to the latest firmware. 3. Go to Jobs > Options > Delete all queue scan jobs. 4. Make sure the hard disk that is installed in the printer is the correct one for the product you are repairing. 5. Check and clean scanner elements. 6. Calibrate the scanner. Service engineer: • In some corner cases, the issue could be related to media movement. Replace the media sensors.

09:03:10 HP DESIGNJET T930, T930PS

- id :

1283

- code :

09:03:10

- description :

CIS B Element is failing

- remede :

Call agent: 1. Clean the scanner of dust and dirt and perform the Scanner Calibration. 2. If the system error persists, upgrade with latest firmware version. Service engineer: 1. Replace CIS B Element. 2. Replace Scanner Controller Board (SCU).

09:04 HP DESIGNJET T930, T930PS

- id :

1284

- code :

09:04

- description :

Library failed to load.

- remede :

Call agent: 1. Reboot the product. 2. Upgrade to the latest firmware.

09:04:10 HP DESIGNJET T930, T930PS

- id :

1285

- code :

09:04:10

- description :

CIS C Element is failing

- remede :

Call agent: 1. Clean the scanner of dust and dirt and perform the Scanner Calibration. 2. If the system error persists, upgrade with latest firmware version. Service engineer: 1. Replace CIS C Element. 2. Replace Scanner Controller Board (SCU).

09:05:10 HP DESIGNJET T930, T930PS

- id :

1286

- code :

09:05:10

- description :

CIS D Element is failing

- remede :

Call agent: 1. Clean the scanner of dust and dirt and perform the Scanner Calibration. 2. If the system error persists, upgrade with latest firmware version. Service engineer: 1. Replace CIS D Element. 2. Replace Scanner Controller Board (SCU)

09:06:10 HP DESIGNJET T930, T930PS

- id :

1287

- code :

09:06:10

- description :

CIS E Element is failing

- remede :

Call agent: 1. Clean the scanner of dust and dirt and perform the Scanner Calibration. 2. If the system error persists, upgrade with latest firmware version. Service engineer: 1. Replace CIS E Element. 2. Replace Scanner Controller Board (SCU).

09:08:11 HP DESIGNJET T930, T930PS

- id :

1288

- code :

09:08:11

- description :

Power cable of the Scanner is failing

- remede :

Service engineer: • Check the condition and connections of the Scanner Power cable, if necessary replace the cable.

09:09:11 HP DESIGNJET T930, T930PS

- id :

1289

- code :

09:09:11

- description :

USB cable of the Scanner is failing

- remede :

Service engineer: • Check the condition of the Scanner USB cable and its connections, if necessary replace the cable.

09:10:04 HP DESIGNJET T930, T930PS

- id :

1290

- code :

09:10:04

- description :

Scanner is in SAFE MODE

- remede :

Service engineer: • Restart the product, if the problem persists replace the SCU.

09:10:10 HP DESIGNJET T930, T930PS

- id :

1291

- code :

09:10:10

- description :

Scanner Controller Board (SCU) is failing

- remede :

Call agent: 1. Turn off the product (2 sec.) using the Power key at the front, then also turn off the power switch at the rear and disconnect the power cable. 2. Perform the Scanner Calibration. 3. If the system error persists, upgrade with latest firmware version. 4. Perform File System Check. 5. Perform the Scanner Validation. Service engineer: 1. Check the USB cable connection. 2. Replace the Scanner SCU. See Scanner Controller Unit (SUP). 3. Check the Scanner USB cable connection and the

11:10 HP DESIGNJET T930, T930PS

- id :

1292

- code :

11:10

- description :

Trailing cable does not seem to be detected

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Check that the trailing cable is correctly connected between the engine PCA and carriage PCA. 2. Check that the trailing cable connectors are not damaged, especially on the E-Box side; replace the trailing cable if necessary. 3. Check that the power cable from the power supply unit is connected to the formatter. 4. Re

21.2:13 HP DESIGNJET T930, T930PS

- id :

1293

- code :

21.2:13

- description :

Failure moving service station

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Check the Primer Tubes. Reconnect the power cord, then turn on the printer. 2. Ensure that the service station path is clear. Remove any visible obstacles (screws, plastic parts, etc.) restricting the movement of the service station. 3. If the carriage has stopped over the service station, on the left of the printer, check that the cutter is not activated. The cutter may be blocking the ca

21:13 HP DESIGNJET T930, T930PS

- id :

1294

- code :

21:13

- description :

Problem with the Service Station motor

- remede :

Call agent: 1. Ensure that the service station path is clear. Remove any visible obstacles (screws, plastic parts, etc.) restricting the movement of the service station. 2. If the carriage has stopped over the service station, on the left of the printer, check that the cutter is not activated. The cutter may be blocking the carriage over the service station, preventing the service station from moving correctly. The cutter is on the right side of the carriage. 3. Perform the service station di

22.0:00 HP DESIGNJET T930, T930PS

- id :

1295

- code :

22.0:00

- description :

Service-station-side ink supply station error

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Perform the ink delivery system diagnostic test to troubleshoot the problem further. Service engineer: 1. Check that the cables between the ink supply station and the engine PCA are not damaged and are properly connected. In case of any damage, replace the cable. 2. Replace the ink supply station on the service station side. 3. Replace

22.1:00 HP DESIGNJET T930, T930PS

- id :

1296

- code :

22.1:00

- description :

Front-panel-side ink supply station error

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Perform the ink delivery system diagnostic test to troubleshoot the problem further. Service engineer: 1. Check that the cables between the ink supply station and the engine PCA are not damaged and are properly connected. In case of any damage, replace the cable. 2. Replace the ink supply station on the front panel side. 3. Replace the

24:10 HP DESIGNJET T930, T930PS

- id :

1297

- code :

24:10

- description :

Error detected in ink tube system

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Perform the Ink Delivery System diagnostic test in order to check that the bongos (pushers) go up and down to pressurize ink in the tube, and the Out of Ink sensors work properly. 2. If the diagnostic test does not find any problem, install new cartridges,and the printhead, and try purging the Ink Supply Tubes again.

26:01 HP DESIGNJET T930, T930PS

- id :

1298

- code :

26:01

- description :

Ink supply error found during IDS diagnostic test (advisory)

- remede :

In the front panel message you can see letters representing the names of the colors of the faulty supplies. Call agent: 1. Reseat the faulty ink supply and repeat the ink delivery system diagnostic test. 2. Replace the faulty ink supply and repeat the ink delivery system diagnostic test. Service engineer: • Replace the left ink supply station.

27:01 HP DESIGNJET T930, T930PS

- id :

1299

- code :

27:01

- description :

Too many nozzles out detected (Advisory)

- remede :

Call agent: 1. Print the gNozzle healthh diagnostic print from the service menu. If printhead shows many nozzles out, replace the printhead. 2. If printhead doesnft show too many nozzles out, run gdrop detector calibrationh. Service engineer: • If printhead doesnft have too many nozzles out and gdrop detection calibrationh doesnft help, replace the drop detector.

39.11:01 HP DESIGNJET T930, T930PS

- id :

1300

- code :

39.11:01

- description :

Media unloaded (Advisory) Plot cut partially and part of the image is kept in the unloaded roll. This warning may happen in the following situations: • When an end of roll 1 is detected because end of media is glued to the core. • Paper has been unloaded before its end due to several reasons. In the cases bellow an excess of friction is causing malfunction in the media input which ends in unexpected media unloads: . Blue hub not completely introduced in the Media Roll core . Black Hub is

- remede :

Call agent: 1. Upgrade the printer to the latest firmware. 2. Ask customer if the advisory has appeared when reaching the end of the roll. In that case it is expected behavior. Tell customer to load new media roll and continue printing. 3. Ask customer to open roll cover and feed media into the media path. a. Check if media sides are brushing the hubs. In that case tell customer to re-position the media roll on the spindle ensuring a margin (.3mm) between the sides of the media and the black

39.12:01 HP DESIGNJET T930, T930PS

- id :

1301

- code :

39.12:01

- description :

Media unloaded (Advisory) Plot cut partially and part of the image is kept in the unloaded roll. This warning may happen in the following situations: • When an end of roll 2 is detected because end of media is glued to the core. • Paper has been unloaded before its end due to several reasons. In the cases bellow an excess of friction is causing malfunction in the media input which ends in unexpected media unloads: . Blue hub not completely introduced in the Media Roll core . Black Hub is

- remede :

Call agent: 1. Upgrade the printer to the latest firmware. 2. Ask customer if the advisory has appeared when reaching the end of the roll. In that case it is expected behavior. Tell customer to load new media roll and continue printing. 3. Ask customer to open roll cover and feed media into the media path. a. Check if media sides are brushing the hubs. In that case tell customer to re-position the media roll on the spindle ensuring a margin (.3mm) between the sides of the media and the black

41:03 HP DESIGNJET T930, T930PS

- id :

1302

- code :

41:03

- description :

Electrical problem (fault, current limit, overheating) in paper-axis motor

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Check for any visible obstacles restricting the movement of the paper advance roller. If there is a wrinkled mass of paper inside the paper path, lift the pinchwheels (using the pinchwheels diagnostic test), and clear the obstruction. 3. Perform the paper drive diagnostic test to troubleshoot the problem further. Service engineer: 1. C

42:03 HP DESIGNJET T930, T930PS

- id :

1303

- code :

42:03

- description :

Electrical problem (fault, current limit, overheating) in scan-axis motor

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. 2. Reconnect the power cord, then turn on the printer. 3. Check for any visible obstacles restricting the movement of the carriage assembly. Remove any obstacle to let the carriage move freely along the whole scan axis. Service engineer: 1. Check that the scan-axis motor cable is undamaged and correctly corrected to the engine PCA. 2. Replace the scan-axis motor. See Scan Axis Motor. 3. Re

45.1:03, 45.1:10 HP DESIGNJET T930, T930PS

- id :

1304

- code :

45.1:03, 45.1:10

- description :

Error in the rewinder 1 system (upper rewinder)

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Remove the paper from roll 1. Reconnect the power cord, then turn on the printer. 2. The rewinder will be tested automatically during boot up. Service engineer: 1. Check that the rewinder 1 cable is undamaged and correctly connected to the engine PCA. 2. Replace the upper roll rewinder.

45.2:03, 45.2:10 HP DESIGNJET T930, T930PS

- id :

1305

- code :

45.2:03, 45.2:10

- description :

Error in the rewinder 2 system (lower rewinder)

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Remove the paper from roll 2. Reconnect the power cord, then turn on the printer. 2. The rewinder will be tested automatically during boot up. Service engineer: 1. Check that the rewinder 2 cable is undamaged and correctly connected to the engine PCA 2. Replace the lower roll rewinder.

46.1:10 HP DESIGNJET T930, T930PS

- id :

1306

- code :

46.1:10

- description :

Error in the upper pump of the PHA blowing system

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Check that the pump cable is undamaged and correctly corrected to the engine PCA. 2. Replace the upper pump.

46.2:10 HP DESIGNJET T930, T930PS

- id :

1307

- code :

46.2:10

- description :

Error in the lower pump of the PHA blowing system

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Check that the pump cable is undamaged and correctly corrected to the engine PCA. 2. Replace the lower pump.

47.5:10 HP DESIGNJET T930, T930PS

- id :

1308

- code :

47.5:10

- description :

Problem at the starwheel lifter motor end of the travel sensor

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Check for any visible obstacles restricting the movement of the starwheel assembly, then clear the obstruction. 3. Perform the scan-axis starwheel diagnostic test to troubleshoot the problem further. Service engineer: 1. Check that the starwheel lifter sensor cable is undamaged and correctly connected to the engine PCA. 2. Replace the

47:03, 47:10 HP DESIGNJET T930, T930PS

- id :

1309

- code :

47:03, 47:10

- description :

Starwheel motor error

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Check for any visible obstacles restricting the movement of the starwheel assembly, then clear the obstruction. 3. Perform the scan-axis starwheel diagnostic test to troubleshoot the problem further. Service engineer: 1. Check that the starwheel assembly cable is undamaged and correctly corrected to the engine PCA. 2. Replace the starw

48:00 HP DESIGNJET T930, T930PS

- id :

1310

- code :

48:00

- description :

PRS Actuator system failure

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Perform the scan-axis PRS diagnostic test to troubleshoot the problem further. Service engineer: 1. Check that the PRS Actuator cable is undamaged and correctly connected to the engine PCA. 2. Replace the printhead-to-paper space solenoid. 3. Replace the engine PCA.

52:10 HP DESIGNJET T930, T930PS

- id :

1311

- code :

52:10

- description :

Drop detector failure

- remede :

Call agent: • Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. Service engineer: 1. Check that the drop detector cable is undamaged and correctly connected to the service station board. 2. Replace the drop detector. See Service Station with Drop Detector. 3. Replace the service station. See Service Station with Drop Detector.

54.4:03 HP DESIGNJET T930, T930PS

- id :

1312

- code :

54.4:03

- description :

Pinchwheel lifter motor error

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Check for any visible obstacles restricting the movement of the pinchwheel assembly, then clear the obstruction. Service engineer: 1. Check that the pinchwheel motor assembly cable is undamaged and correctly connected to the engine PCA. 2. Replace the pinchwheel lifter motor. See Pinch Wheel Assembly. 3. Replace the engine PCA.

55:10 HP DESIGNJET T930, T930PS

- id :

1313

- code :

55:10

- description :

Cannot access the line sensor EEPROM

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Perform the carriage test to troubleshoot the problem further. Service engineer: 1. Replace the line sensor. See Line Sensor. 2. Replace the carriage PCA. See Engine PCA.

56:01 HP DESIGNJET T930, T930PS

- id :

1314

- code :

56:01

- description :

Drive roller analog encoder homing failed

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Perform the paper path test to troubleshoot the problem further. Service engineer: 1. Replace the encoder disk and encoder sensor. 2. Replace the engine PCA. See Engine PCA.

59.1:09 HP DESIGNJET T930, T930PS

- id :

1315

- code :

59.1:09

- description :

Two electrical parts have been replaced at the same time

- remede :

Service engineer: • Replace one part at a time, and restart the printer before replacing another.

59.2:00 HP DESIGNJET T930, T930PS

- id :

1316

- code :

59.2:00

- description :

An unsupported or reused part has been installed

- remede :

Service engineer: • Install only new parts recommended by HP for this printer.

59.3:10 HP DESIGNJET T930, T930PS

- id :

1317

- code :

59.3:10

- description :

Wrong information stored on CryptoAsic

- remede :

Call agent: • Switch the power off at the rear of the printer, wait two minutes, then switch it back on again. Service engineer: • Escalate the case to Level 3, requesting new CryptoAsic SIM licenses. Update the CryptoAsic SIM with the delivered licenses.

59.4:10 HP DESIGNJET T930, T930PS

- id :

1318

- code :

59.4:10

- description :

CryptoAsic failure

- remede :

Call agent: • Switch the power off at the rear of the printer, wait two minutes, then switch it back on again. Service engineer: 1. Reseat the CryptoAsic SIM PCA. 2. Order an CryptoAsic SIM PCA Service Kit. Escalate to Level 3 providing printer Serial Number, Product Number, and the serial number of the CryptoAsic SIM Service Kit. Replace the CryptoAsic SIM PCA. Write in an empty USB the file provided by Level 3. Plug the USB in the printer and reboot. If booting fails, enable diagnostic pac

59.5:19 HP DESIGNJET T930, T930PS

- id :

1319

- code :

59.5:19

- description :

CryptoAsic type mismatch

- remede :

Call agent: • Switch the power off at the rear of the printer, wait two minutes, then switch it back on again. Service engineer: 1. Order an CryptoAsic SIM PCA Service Kit. Escalate to Level 3 providing printer Serial Number, Product Number, and the serial number of the CryptoAsic SIM Service Kit. Replace the CryptoAsic SIM PCA. Write in an empty USB the file provided by Level 3. Plug the USB in the printer and reboot. If booting fails, enable diagnostic package with the USB and provide logs

59.6:19 HP DESIGNJET T930, T930PS

- id :

1320

- code :

59.6:19

- description :

Printer serial number mismatch

- remede :

Call agent: • Switch the power off at the rear of the printer, wait two minutes, then switch it back on again. Service engineer: 1. Order an CryptoAsic SIM PCA Service Kit. Escalate to Level 3 providing printer Serial Number, Product Number, and the serial number of the CryptoAsic SIM Service Kit. Replace the CryptoAsic SIM PCA. Write in an empty USB the file provided by Level 3. Plug the USB in the printer and reboot. If booting fails, enable diagnostic package with the USB and provide logs

59.7:14 HP DESIGNJET T930, T930PS

- id :

1321

- code :

59.7:14

- description :

CryptoAsic generic error

- remede :

Call agent: • Switch the power off at the rear of the printer, wait two minutes, then switch it back on again. Service engineer: • Order an CryptoAsic SIM PCA Service Kit. Escalate to Level 3 providing printer Serial Number, Product Number, and the serial number of the CryptoAsic SIM Service Kit. Replace the CryptoAsic SIM PCA. Write in an empty USB the file provided by Level 3. Plug the USB in the printer and reboot. If booting fails, enable diagnostic package with the USB and provide logs

60.1:11 HP DESIGNJET T930, T930PS

- id :

1322

- code :

60.1:11

- description :

Initialization error (cannot read RFID tag)

- remede :

Call agent: 1. Switch the power off at the rear of the printer, wait two minutes, then switch it back on again. 2. Check the power cord; try connecting it to another power socket. Service engineer: 1. Check that the RFID device is correctly connected. 2. If the error persists, get the diagnostic package (see Appendix C: Obtaining the diagnostics package) and contact Level 3 providing print Serial Number and Product Number.

60.2:17 HP DESIGNJET T930, T930PS

- id :

1323

- code :

60.2:17

- description :

Initialization error (RFID has incorrect data)

- remede :

Call agent: 1. Switch the power off at the rear of the printer, wait two minutes, then switch it back on again. 2. Check the power cord; try connecting it to another power socket. Service engineer: 1. Check that the RFID device is correctly connected. 2. If the error persists, get the diagnostic package (see Appendix C: Obtaining the diagnostics package) and contact Level 3 providing print Serial Number and Product Number.

61:01 HP DESIGNJET T930, T930PS

- id :

1324

- code :

61:01

- description :

Incorrect or unsupported file format (advisory)

- remede :

Call agent: 1. Check whether the printer supports the file format. Formats such as PS, PDF, TIFF, and JPEG are supported by PostScript printers only. 2. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 3. Check the printer’s graphic language setting (see the user's guide). 4. Resend the file to the printer. 5. Update the firmware.

61:04.1 HP DESIGNJET T930, T930PS

- id :

1325

- code :

61:04.1

- description :

PostScript fonts seem to be missing (advisory)

- remede :

Call agent: • Update the firmware to re-install the fonts.

61:04.2 HP DESIGNJET T930, T930PS

- id :

1326

- code :

61:04.2

- description :

Unknown PostScript ID sent to printer (advisory)

- remede :

Call agent: • Update the firmware.

61:08 HP DESIGNJET T930, T930PS

- id :

1327

- code :

61:08

- description :

Incor rect paper type specified in job (advisory)

- remede :

Call agent: • Change the paper type and resend the job.

61:08.1 HP DESIGNJET T930, T930PS

- id :

1328

- code :

61:08.1

- description :

Job cannot be printed because it is password-protected (advisory)

- remede :

Call agent: • Resend the job without password protection.

61:08.2 HP DESIGNJET T930, T930PS

- id :

1329

- code :

61:08.2

- description :

Job contains format errors or incorrect settings (advisory)

- remede :

Call agent: 1. Ensure that the file format sent is supported by the printer. 2. Resend the job using the Embedded Web Server.

61:09 HP DESIGNJET T930, T930PS

- id :

1330

- code :

61:09

- description :

Unexpected end of job (advisory)

- remede :

Call agent: 1. Resend the job. 2. Resend the job using the Embedded Web Server.

61:10 HP DESIGNJET T930, T930PS

- id :

1331

- code :

61:10

- description :

Job timed out (advisory)

- remede :

A slow computer processing complex files can pause for longer than the default printer timeout, in which case some elements of the job may be lost. Call agent: 1. Increase the I/O timeout using the printer's front panel (see 'Configure network settings' in the user’s guide). 2. Resend the job from a faster computer. 3. Resend the job using the Embedded Web Server. 4. Use the “print to file” option in the driver and copy the resulting file to a USB flash drive. Print from the USB flash drive.

63:04 HP DESIGNJET T930, T930PS

- id :

1332

- code :

63:04

- description :

Network interface error

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Check that the network cable is correctly connected to the network interface. 3. Update the firmware. Service engineer: 1. If the printer is blocked showing the system error persistently; check that the network interface card (including the riser) are correctly connected. 2. If the printer is blocked showing the system error persistent

63:10 HP DESIGNJET T930, T930PS

- id :

1333

- code :

63:10

- description :

Network interface error

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Check that the network cable is correctly connected to the network interface. 3. Update the firmware. Service engineer: 1. Check that the network interface card (including the riser) are correctly connected. 2. Replace the network interface card.

63:20 HP DESIGNJET T930, T930PS

- id :

1334

- code :

63:20

- description :

Potential problem in the network interface (advisory)

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Check that the network cable is correctly connected to the network interface. 3. Update the firmware. Service engineer: 1. Check that the network interface card (including the riser) are correctly connected. 2. Replace the network interface card.

71:03 HP DESIGNJET T930, T930PS

- id :

1335

- code :

71:03

- description :

Out of memory

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Resend the job with one or more of the following changes: • Decrease resolution to 3 dpi. • Select Economode print mode. • Select the Send job as bitmap option.

71:08 HP DESIGNJET T930, T930PS

- id :

1336

- code :

71:08

- description :

Insufficient display list

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Resend the job with one or more of the following changes: • Decrease resolution to 3 dpi. • Select Economode print mode. • Select the Send job as bitmap option.

72.02 HP DESIGNJET T930, T930PS

- id :

1337

- code :

72.02

- description :

A service calibration should be performed (advisory)

- remede :

Call agent: • To find out which service calibration to perform, print the calibration status. At the front panel, press , then , then Internal prints > Service information prints > Print calibration status. Perform whichever calibration is needed.

74.08:04 HP DESIGNJET T930, T930PS

- id :

1338

- code :

74.08:04

- description :

Firmware update problem

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Try again to update the firmware. If necessary, see Appendix B: Updating firmware in boot mode. 3. Download the firmware file again, as the file that you have may be corrupted. Service engineer: • Replace the front panel.

74.1:04 HP DESIGNJET T930, T930PS

- id :

1339

- code :

74.1:04

- description :

Error uploading paper preset (advisory)

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Ensure that the connection between the computer and the printer is functioning properly. 3. Try again to upload the paper preset. 4. Ensure that the version of the paper preset is compatible with the firmware version in the printer. You can check this on the same Web page from which you downloaded the paper preset.

74:01 HP DESIGNJET T930, T930PS

- id :

1340

- code :

74:01

- description :

Error uploading firmware update file (advisory)

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Ensure that the connection between the computer and the printer is functioning properly. 3. Try again to upload the firmware update file.

76:03 HP DESIGNJET T930, T930PS

- id :

1341

- code :

76:03

- description :

The hard disk is full

- remede :

Call agent: 1. Remove any unnecessary files from the hard disk using the Embedded Web Server. 2. Run the Hard Disk Recovery Utility.

78.1:04 HP DESIGNJET T930, T930PS

- id :

1342

- code :

78.1:04

- description :

Paper settings area missing in paper settings file (advisory)

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Update the firmware.

78:08 HP DESIGNJET T930, T930PS

- id :

1343

- code :

78:08

- description :

Paper does not support borderless printing (advisory)

- remede :

Call agent: • Use a paper type that supports borderless printing. NOTE: This should be resolved by the customer without assistance.

79.2:04 HP DESIGNJET T930, T930PS

- id :

1344

- code :

79.2:04

- description :

Generic Operating System error

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Update the firmware. 3. See Appendix A: How to troubleshoot system error 79:4 and 79.2:4. 4. Information available by pressing while viewing the system error screen; or, preferably, provide the diagnostic package.

79:03 HP DESIGNJET T930, T930PS

- id :

1345

- code :

79:03

- description :

Generic firmware error

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Update the firmware. 3. Information available by pressing while viewing the system error screen; or, preferably, provide the diagnostic package.

79:04 HP DESIGNJET T930, T930PS

- id :

1346

- code :

79:04

- description :

Generic firmware error

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Update the firmware. 3. See Appendix A: How to troubleshoot system error 79:4 and 79.2:4. 4. Information available by pressing while viewing the system error screen; or, preferably, provide the diagnostic package.

80:03 HP DESIGNJET T930, T930PS

- id :

1347

- code :

80:03

- description :

Stacker overdrive motor error

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Test the cutter. Perform a 'Form Feed & Cut', and verify the paper can be cut. See The cutter does not cut well. 3. Perform the stacker overdrive motor diagnostic test to troubleshoot the problem further. Service engineer: 1. Check that the stacker overdrive motor cable is undamaged and correctly connected to the engine PCA. 2. Rep

81:01 HP DESIGNJET T930, T930PS

- id :

1348

- code :

81:01

- description :

Paper servo shutdown, possible paper jam

- remede :

If this error is reported during printer setup, it may indicate that the printer has been dropped during transportation, causing structural damage. Before continuing with the 81:1 troubleshooting, first look for structural damage. To identify the structural damage, look for the following three things: • Persistent 81:1 error codes • Platen fingers rubbing on the roller surface, leaving black marks on the roller • A gap in the platen beam. If there is any gap in the vertical direction bet

86:01 HP DESIGNJET T930, T930PS

- id :

1349

- code :

86:01

- description :

Scan axis servo shutdown, possible paper jam

- remede :

Call agent: 1. Open the window and check for any visible obstacles restricting the movement of the carriage assembly. If there is a wrinkled mass of paper inside the paper path, lift the pinchwheels and clear the obstruction. 2. Turn off the printer and unplug the power cord. Try to move the carriage manually. Check that the cutter disengages correctly and that the carriage is not blocked by the service station. 3. Perform the scan-axis diagnostic to obtain further information on the problem.

87:01 HP DESIGNJET T930, T930PS

- id :

1350

- code :

87:01

- description :

Problem reading the scan-axis encoder (advisory)

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Reconnect the power cord, then turn on the printer. 2. Ensure that the encoder strip is clean. If it is dirty, clean it, paying special attention to the area near the service station. 3. Replace the carriage PCA.

89:03 HP DESIGNJET T930, T930PS

- id :

1351

- code :

89:03

- description :

Stacker ramps motor error

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Remove all paper from the stacker and basket. Reconnect the power cord, then turn on the printer. 2. Perform the stacker ramps motor diagnostic test to troubleshoot the problem further. Service engineer: 1. Check that the stacker ramps motor cable is undamaged and correctly connected to the engine PCA. 2. Replace the stacker ramps motor.

90.1:03 HP DESIGNJET T930, T930PS

- id :

1352

- code :

90.1:03

- description :

Diverter valves motor error, valves stalled in High position

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Remove all paper from the stacker and basket. Reconnect the power cord, then turn on the printer. 2. Perform the output valve test to troubleshoot the problem further. 3. Perform the output valves calibration to check system performance, and troubleshoot further. Service engineer: 1. Check that the diverter valves motor cable is undamaged and correctly connected to the engine PCA. 2. Perfo

90.2:03 HP DESIGNJET T930, T930PS

- id :

1353

- code :

90.2:03

- description :

Diverter valves motor error, valves stalled in Low position

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Remove all paper from the stacker and basket. Reconnect the power cord, then turn on the printer. 2. Perform the output valve test to troubleshoot the problem further. 3. Perform the output valves calibration to check system performance, and troubleshoot further. Service engineer: 1. Check that the diverter valves motor cable is undamaged and correctly connected to the engine PCA. 2. Repla

90:03, 90.0:03 HP DESIGNJET T930, T930PS

- id :

1354

- code :

90:03, 90.0:03

- description :

Diverter valves motor error

- remede :

Call agent: 1. Use the power switch at the rear to turn off the printer, then disconnect the power cord. Remove all paper from the stacker and basket. Reconnect the power cord, then turn on the printer. 2. Make sure customer has FW release MRY_3__xx or newer. 3. Perform the output valve test to troubleshoot the problem further. 4. Perform the output valves calibration to check system performance, and troubleshoot further. Service engineer: 1. Check that the diverter valves motor cable is u

93.0.n:10 HP DESIGNJET T930, T930PS

- id :

1355

- code :

93.0.n:10

- description :

Ink pressure error in first test during in Printhead filling for color n n indicates the failing color: • n=0 stands for photo black • n=1 stands for gray • n=2 stands for matte black • n=3 stands for cyan • n=4 stands for magenta • n=5 stands for yellow

- remede :

Call agent: • If no SE 93.2.n:1 appears it means that the issue was fixed after the customer reseated the printhead.

93.1.n:10 HP DESIGNJET T930, T930PS

- id :

1356

- code :

93.1.n:10

- description :

Ink pressure error in Second spitting test during in Printhead filling for color n n indicates the failing color: • n=0 stands for photo black • n=1 stands for gray • n=2 stands for matte black • n=3 stands for cyan • n=4 stands for magenta • n=5 stands for yellow

- remede :

Call agent: • During the tube filling, the first spitting test with the printhead failed the temperature check in color n. If no SE 93.3.n:1 appears it means that the issue was fixed after the customer reseated the printhead.

93.2.n:10 HP DESIGNJET T930, T930PS

- id :

1357

- code :

93.2.n:10

- description :

Temperature error in First test during in Printhead filling for color n n indicates the failing color: • n=0 stands for photo black • n=1 stands for gray • n=2 stands for matte black • n=3 stands for cyan • n=4 stands for magenta • n=5 stands for yellow

- remede :

Call agent: 1. After the customer reseated the printhead, the printer failed in the second test of ink pressure for color n. This means that color n in the printhead might not be filled with ink, or the tubes are leaking. 2. Run primer and Ink Delivery System tests, and troubleshoot accordingly. 3. If tests run successfully: a. Moisten tube septums with water. b. Upgrade firmware. c. Purge tubes again with new printhead and new supplies (6ml min per color).

93.3.n:10 HP DESIGNJET T930, T930PS

- id :

1358

- code :

93.3.n:10

- description :

Temperature error in second spitting test during in Printhead filling for color n n indicates the failing color: • n=0 stands for photo black • n=1 stands for gray • n=2 stands for matte black • n=3 stands for cyan • n=4 stands for magenta • n=5 stands for yellow

- remede :

Call agent: During the tube filling, after the customer reseated the printhead, the second spitting test with the printhead failed the temperature check in color n. This means that color n in the printhead is not filled with ink. 1. Depending on the colors failing the test, troubleshoot according to: a. If colors -1-2 are missing, issue might be due to Service Station Side Ink Supply Station. Run Ink delivery System test. b. If colors 3-4-5 are missing, issue might be due to Front Panel Side